Flipsky Dual 75100 14-84V 2x100A + BT
Kategória:
Kolobežky
Plne programovateľný sínusoý kontroler pre elektrické kolobežky (bicykle skateboarde čokoľvek). Vhodná náhrada napr za kontrolery Laotie ES18 ES19 Ti30 a ktorékoľvek iné.
Flipsky Dual 75100 With Aluminum PCB Based On VESC For Electric Skateboard / Scooter / Ebike Speed Controller + Flipsky Wireless Bluetooth Module 2.4G for VESC&VESC Tool Electric Skateboard
Size:L107mm x W103mm x H18.5mm
Voltage:14-84V (4-20S safey)
Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting and ambient temperature around the device!
BEC:5V@1A
Support BLDC square wave mode control and FOC sine wave mode
Firmware: latest (firmware update supported)
ERPM:150000
Control Interface Ports:USB,CAN,UART
Supported Sensors:ABI,HALL,AS5047,AS5048A
Input Set Support:PPM,ADC,NRF,UART
Wire Size: 12AWG
Programmable: Yes
Regenerative Capacity: Yes
Here below video and blog links FYI.
YouTube: Black
Material: PCB
Package Contents:
1 * Speed Controller
1 * BT module
Flipsky Wireless Bluetooth Module 2.4G for VESC&VESC Tool Electric Skateboard
Kindly Reminder: This bluetooth module can only support Android mobile device.
Used to communicating between the VESC and VESC Tool (mobile) over BLE. Note that the UART port on the VESC must be enabled with a baud rate of 115200 for this to work. The UART port on VESC can work only under 115200 baud
Operating voltage: 2.0V ~ 12V Onboard Chip: NRF51822
Actual use distance: The distance to communicate with VESC is about 15 meters
Frequency range: 2.4GHz
2.4 GHz multiprotololl RF receiver
ARM Cortex-M0 32 bit processor
256kB flash & 16kB RAM
PCB size:27mm x 13mm
2.0mm seven-pin four-wire connector length:90mm
Antenna length:145mm
net weight:3.5g
Type: V6
Colour: Black
Material: composite material
360€ + poštovné.
Na dobierku posielam až po prijatí zálohy(30% z ceny) na účet.
Flipsky Dual 75100 With Aluminum PCB Based On VESC For Electric Skateboard / Scooter / Ebike Speed Controller + Flipsky Wireless Bluetooth Module 2.4G for VESC&VESC Tool Electric Skateboard
Size:L107mm x W103mm x H18.5mm
Voltage:14-84V (4-20S safey)
Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting and ambient temperature around the device!
BEC:5V@1A
Support BLDC square wave mode control and FOC sine wave mode
Firmware: latest (firmware update supported)
ERPM:150000
Control Interface Ports:USB,CAN,UART
Supported Sensors:ABI,HALL,AS5047,AS5048A
Input Set Support:PPM,ADC,NRF,UART
Wire Size: 12AWG
Programmable: Yes
Regenerative Capacity: Yes
Here below video and blog links FYI.
YouTube: Black
Material: PCB
Package Contents:
1 * Speed Controller
1 * BT module
Flipsky Wireless Bluetooth Module 2.4G for VESC&VESC Tool Electric Skateboard
Kindly Reminder: This bluetooth module can only support Android mobile device.
Used to communicating between the VESC and VESC Tool (mobile) over BLE. Note that the UART port on the VESC must be enabled with a baud rate of 115200 for this to work. The UART port on VESC can work only under 115200 baud
Operating voltage: 2.0V ~ 12V Onboard Chip: NRF51822
Actual use distance: The distance to communicate with VESC is about 15 meters
Frequency range: 2.4GHz
2.4 GHz multiprotololl RF receiver
ARM Cortex-M0 32 bit processor
256kB flash & 16kB RAM
PCB size:27mm x 13mm
2.0mm seven-pin four-wire connector length:90mm
Antenna length:145mm
net weight:3.5g
Type: V6
Colour: Black
Material: composite material
360€ + poštovné.
Na dobierku posielam až po prijatí zálohy(30% z ceny) na účet.
